Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
This article following next pertaining to A Step-by-Step Guide to Installing a Bathtub is truly interesting. Don't bypass it.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Rather than employing a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your shower room if you have already purchased a new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your tools and also product list need to consist of the following:
Planning for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The process of eliminating the existing taps can be rather bothersome because of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the spirit level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the supply of water as well as check all joints and new pipework for leaks as well as tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Secure the faucet in position with the producer offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and fittings. They are offered in tubes and cartridges, as well as are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section about How to Install a Bathtub Yourself. Thank you so much for taking a few minutes to read through our article post. Enjoyed our posting? Please share it. Help another person check it out. Many thanks for your time. Please visit our site back soon.
Request Appointment Report this page